Interference issues of LED driver power supplies are not easy to resolve. The main reason is that the impacts brought by interference are often unpredictable and hard to guard against. To properly handle various types of interference, it is necessary to identify the root causes.
An LED driver power supply first rectifies industrial-frequency AC into DC, then inverts it into high-frequency AC, and finally outputs stable DC voltage through rectifier and filter circuits. Therefore, it inherently contains substantial harmonic interference. Meanwhile, electromagnetic interference is also generated by the leakage inductance of the transformer and spikes caused by the reverse recovery current of output diodes. Interference sources inside switching power supplies are mainly concentrated on components with drastic voltage and current variations, notably switching transistors, diodes and high-frequency transformers.
The switching circuit is one of the primary interference sources of switching power supplies (this also applies to LED street light drivers and LED tunnel light drivers). It mainly consists of switching transistors and high-frequency transformers. It generates pulses with high-amplitude du/dt, wide frequency bands and rich harmonic content.This pulse interference arises mainly because the load of the switching transistor is the primary winding of the high-frequency transformer, an inductive load. At the moment the switching transistor turns on, a large inrush current flows through the primary winding, and a high surge spike voltage appears across the winding. When the switching transistor turns off, part of the energy fails to transfer from the primary winding to the secondary winding due to leakage flux. The energy stored in the inductor, together with capacitors and resistors in the collector circuit, forms a damped oscillation with spikes superimposed on the turn-off voltage, creating turn-off voltage spikes.Interruption of the supply voltage produces magnetization inrush current transients similar to those occurring at primary energization. Such transients are conducted electromagnetic interference. They affect the primary side of the transformer and feed conducted interference back to the power distribution system, causing grid harmonic electromagnetic interference and threatening the safe and economical operation of other equipment.
In rectifier circuits, a reverse current occurs when the output rectifier diode turns off. The time for this current to return to zero is related to junction capacitance and other factors. Diodes whose reverse current quickly drops to zero are known as hard-recovery diodes. Under the influence of transformer leakage inductance and other parasitic parameters, hard-recovery diodes generate strong high-frequency interference, which can reach tens of MHz.A large forward current flows through the rectifier diode in the high-frequency rectifier loop during forward conduction. When reverse-biased and turning off, abundant charge carriers accumulate in the PN junction. Before these carriers disappear, current flows backward, and the reverse recovery current drops sharply, resulting in a large current variation.
The high-frequency switching current loop formed by the primary winding of the high-frequency transformer, switching transistor and filter capacitor may produce strong spatial radiation and radiated interference. If the filter capacitor has insufficient capacitance or poor high-frequency characteristics, its high-frequency impedance will allow high-frequency current to conduct into the AC mains in differential mode, forming conducted interference.It should be noted that the di/dt of the reverse recovery current of rectifier diodes is far greater than that of freewheeling diodes. As EMI sources, rectifier diodes produce interference with high intensity and wide bandwidth. Nevertheless, the voltage jump generated by rectifier diodes is much smaller than that occurring during the turn-on and turn-off of power switching transistors. Therefore, the |dv/dt| effect of rectifier diodes can sometimes be neglected, and the rectifier circuit can be studied as part of the EMI coupling path.
Switching power supplies operate at high frequencies, so stray capacitance cannot be ignored.On the one hand, the insulating sheet between the heat sink and the collector of the switching transistor has a large contact area and thin thickness. Its stray capacitance cannot be ignored at high frequencies. High-frequency current flows through this stray capacitance to the heat sink and then to chassis ground, producing common-mode interference.On the other hand, stray capacitance exists between the primary and secondary windings of the pulse transformer. It can directly couple primary-side voltage to the secondary side and induce common-mode interference on the two DC output power lines.
Within the conducted interference frequency band (<30 MHz), the coupling paths of most switching power supply interference can be described by circuit networks. However, every practical component in a switching power supply — resistors, capacitors, inductors, switching transistors and diodes — carries stray parameters. The wider the frequency band under study, the higher the order of the equivalent circuit.The equivalent circuit of a switching power supply, including component stray parameters and inter-component coupling, is therefore much more complex. At high frequencies, stray parameters strongly affect the characteristics of coupling paths, and stray capacitance acts as an EMI coupling channel.In addition, high-power switching transistors usually require heat sinks. The stray capacitance between the switching transistor and its heat sink cannot be ignored at high frequencies; it can create radiated interference into space and common-mode conducted interference on power lines.
Three approaches can be adopted to solve EMI problems in switching power supplies:
Reduce interference signals generated by the interference source;
Cut off the propagation path of interference signals;
Improve the immunity of susceptible circuits.
The main EMI control technologies for switching power supplies include circuit optimization, EMI filtering, component selection, shielding and anti-interference PCB design.
Soft-switching Technology: Inductors and capacitors are added to conventional hard-switching circuits. Using LC resonance, du/dt and di/dt during switching transitions are reduced. The voltage falls before the current rises at turn-on, or the current falls before the voltage rises at turn-off, eliminating voltage-current overlap.
Switching Frequency Modulation: The switching frequency fc is modulated to spread energy concentrated at fc and its harmonics (2fc, 3fc …) over adjacent frequency bands, lowering the EMI amplitude at each discrete frequency point. This method does not reduce the total interference energy, but spreads noise across the spectrum so that no single frequency point exceeds EMC limits. Two common implementations are random frequency and frequency modulation.
Component Selection: Select components that are less prone to generating, conducting and radiating noise. Special attention should be paid to diodes and wound components such as transformers. Fast recovery diodes with low reverse recovery current and short recovery time are ideal for high-frequency rectification stages of switching power supplies.
Active Common-mode EMI Suppression: A compensation EMI noise voltage, which is exactly anti-phase to the dominant switching voltage waveform causing EMI, is extracted from the main circuit to cancel the original switching voltage.
Filtering: One major purpose of an EMI filter is to achieve high insertion loss within 150 kHz ~ 30 MHz while introducing no attenuation to the 50 Hz mains signal, so rated voltage and current can pass through smoothly, subject to size constraints.Any conducted interference on power lines can be represented as differential-mode and common-mode signals. Generally, differential-mode interference has low amplitude and low frequency with mild effects; common-mode interference features high amplitude and high frequency and can radiate through conductors, leading to severe interference. Therefore, the most effective way to suppress conducted interference and keep EMI below EMC limits is to install EMI filters at the input and output of switching power supplies.
PCB Design: Anti-interference PCB design covers layout, routing and grounding, aiming to reduce electromagnetic radiation and crosstalk between circuits on the board. The optimal layout strategy is similar to electrical design. After the PCB outline and dimension are finalized, high-priority components (oscillators, crystal oscillators, etc.) are placed, followed by all other components arranged according to functional circuit blocks.
Snubber Circuits for EMI Reduction: Built with linear impedance stabilization networks, they suppress potential interference on mains lines, including power-line disturbances, electrical fast transients, surges, voltage fluctuations and harmonics. These disturbances have limited impact on ordinary linear regulated power supplies but significantly affect high-frequency switching power supplies.
Power-line interference can be filtered by power line filters. A well-designed EMI filter for switching power supplies shall effectively suppress both differential-mode and common-mode interference on the mains.